Handler Etcher Catcher and Sandblasters

Perfect for Etching
Using Aluminum Oxide

 52CSU ETCHER CATCHER
Handler's new Etcher Catcher collects dusts created by the use of aluminum oxide blasting pencils. Offered in three configurations, the Etcher Catcher is constructed to be ergonomically accommodating when used with hand held blasting pencils, preventing dusts from collecting
on table tops and surrounding areas. The Etcher Catcher is available in three configurations:
52 Etcher Catcher with filter only - For light office use.
52CFI Etcher Catcher with filter and external 3" flange - For use with your dust collector.
52CSU Etcher Catcher with filter and self-contained dust collector

Shipping Wgt.: 16 lbs [7.3 Kg]
Unit Dimensions: 11” wide x 16” deep x 9” high [27.9cm x 40.6cm x 22.8cm]

Sandblasters and Air Abrasives
51 Sandblaster
 A table top sandblaster for use with Sand, Glass Beads or Walnut Shells. The 51 is designed to clean or treat the surfaces of precious castings e.g. copings, pontics, inlays, etc. Its compact size, 10” wide x 10” deep x 14” high [25cm x 25cm x 36cm], with hinged, frontal access door, rubber side glove, large 5” [13cm] square window, lever air control valve and 3” [7.6cm] diameter exhaust port allows for placement in a small lab area. Shipped complete with 3’ x 1/2” [8cm x 1cm] air line hose, interior light, 5 lbs [2.3 Kg] of medium sand abrasive, and filter bag.
The 51 is an excellent addition to any laboratory. Constructed of heavy gauge sheet steel and finished in a durable, baked coating.
Shipping Wgt.: 17 lbs [7.7 Kg]
Unit Dimensions: 10” wide x 10” deep x 14” high [25cm x 25cm x 36cm]

51GB glass beads
 Medium Glass Beads abrasive for cleaning and blasting of precious and non-precious metals for surface preparation of dental appliances.
Shipping Wgt.: 5lbs [2.3 Kg]

51A Replacement Sand
 A medium grit silica for sand blasting and cleaning the surfaces of precious and non-precious metals prior to processing of dental appliances, crowns, etc.
Shipping Wgt.: 5 lbs [2.3 Kg]

51WS Walnut Shells
 20 lbs [9.1 Kg] walnut shells for use in removing investment and plaster from appliances. Must be utilized with higher air pressure and larger office.
Shipping Wgt.: 20 lbs [9.1 Kg]
78-1 Atlas Junior Vibrator
 A three speed vibrator for use by the dentist or smaller laboratory. This is designed for
compactness, longevity and intermittent use. Its 4” [10cm] diameter, removable, rubber covered table top makes it an ideal addition to any small lab workbench where a vibrator will be utilized for short periods. The Atlas Jr. is available in 115 Volts/60Hz. 115 Volts/50Hz, 230 Volts/50Hz, or 230 Volts/60Hz models may be purchased at additional cost. Finished in a durable, baked coating with resista-move rubber suction cupped feet.
Shipping Wgt.: 5 lbs [2.3 Kg]
Unit Dimensions: 4 1/2” wide x 4 1/2” deep x 4” high [11cm x 11cm x 10cm]
78-RK Atlas Heavy Duty Tri-Speed vibrator
 The NEW Handler 78-RK Heavy Duty Vibrator is built for durability and rugged use. The newly designed 78-RK has two frequencies each with variable speed. The HIGH and LOW are variable to allow a technician to vibrate a mixing bowl or flask at the correct speed for the plaster, stone or viscous solution to de-bubble. The fully covered larger rubber table is built to hold larger flasks and mixing bowls.
The rubber top is removable for easy cleaning and replacement. Four soft rubber feet hold the 78-RK in place during the heaviest vibrating cycles.
The unit is coated with a baked enamel finish. Built to last for many years.
Available in standard 115V/60Hz: 115V/50Hz, 220V/50Hz, 220V/60Hz at additional cost.
Shipping Weight:13 lbs Unit Dimensions: 8”W x 6 1/2”D x 4 1/2”H