A Full Line of Protective Shields and Splash Hoods are Produced by Handler.

Splash hoods in various designs and sizes to fit your requirements are available with and without lights, suction inlets and internal dust/pumice pans.
Fishmouths, which may be used on the benchtop to collect dusts from handpiece grinding or polishing motors, are built for durability and function.
Protective shields are manufactured in various configurations to help protect the technician and comply with OSHA standards.
26SHLD Safety Shield
 Designed for adjustable protection, the 26SHLD may be mounted on a lathe, table top or Model Trimmer. Adapting it to a base bolt hole, or drilling a hole to accommodate the machine bolt mounted base, will allow mounting to a sturdy surface.
Shipping Wgt.: 1 lb [0.5 Kg]
Unit Dimensions: 8” wide x 13” high (adjustable) [20.3cm x 33cm]

32SHLD Safety Shield
Handler designed the 32SHLD to provide adjustable protection against flying debris. This is a must for OSHA compliance.
It’s clear acrylic 6” X 8” shield is attached to a 13” adjustable arm. A strong magnetic base is supplied with each unit to allow the unit to adhere to magnetic surfaces.

The magnetic base may be removed for the adjustable arm to be attached to a non-magnetic surface using a wood screw or a machine bolt. The shield should be located at Model Trimmers, Polishing Motors and any other work station where dust and debris are present.
No. P32SHLD-01 Replacement Shields
Shipping Wgt.: 1 lb [0.5 Kg]
Unit Dimensions:
8” wide x 13” high (adjustable) [20.3cm x 33cm]
79 The Protector
Handler designed this shield of clear acrylic to help protect against flying debris. The Protector is manufactured of heavy 3/8” clear acrylic and fitted with non-skid soft vinyl feet. It is bent at a convenient angle to allow the user to view work in progress while helping to protect against grinding and polishing dusts.

The front section of the shield is shaped to allow the technician to work close to the chuck area. Built to help meet OSHA standards, the Protector provides clear viewing protection from flying debris created by rotary grinding or polishing operations.
It is a necessary companion for Handler Splash Hoods and Fishmouths.
Shipping Wgt.: 2 lbs [1 Kg]
Unit Dimensions: 8” high x 9 3/4” deep x 7” wide
[20cm x 25cm x 18cm]

86B STA-KLEEN Shield
 A clear acrylic shield for placement onto your existing or new splash hood. Manufactured of clear acrylic, the 6” wide x 9” long [15cm x 23cm] shield is adjustable to any vertical position within 180 degrees for maximum protection from flying debris and wet pumice.
Wipes clean with a damp cloth and adaptable to most splash hoods, this protective shield is a MUST for proper protection of laboratory personnel, while stopping splattering pumice stains.
Shipping Wgt.: 1 lb [0.5 Kg]
Unit Dimensions:
6” wide x 9” long [15cm x 23cm]
87210 Fishmouth
 This fishmouth is designed for use on the bench top. Supplied with a 5 1/2” x 3” [14cm x 8cm] diameter rear duct, the 87210 may be connected to a dust collector via flexible ducting or directly into a 210BG Blast Gate which is mounted on the vertical riser of a laboratory bench. Manufactured of Quality Resin which is impervious to germicides. This fishmouth is contoured for use with a Lathe or a handpiece.
Shipping Wgt.: 3 lbs [1.4 Kg]
Unit Dimensions: 6 3/4” high x 15” deep x 6 1/2” wide [38cm x 20cm x 16cm]

87 Fishmouth
 For use on the bench top to assist in the collection of grinding and polishing debris while connected to a dust collector. The fishmouth is a widemouthed type hood which directs debris created by lathe or handpiece operations into a dust collector.
Manufactured of Quality Resin which is impervious to germicides, the 87 is fitted with its own 3” [7.6cm] diameter suction cut-off. The fishmouth is contoured for use with a Lathe or a handpiece.
Shipping Wgt.: 3 lbs [1.4 Kg]
Unit Dimensions: 6 3/4” high x 11 1/2” deep x 6 1/2” wide [30cm x 19cm x 17cm]