16B-1 Lathe with Chuk Changer
$1,200.50
16B-1 Lathe with Chuk Changer is the model 26 high base lathe with the 16 Chuk/Changer factory-installed on the right-hand side. The 16B-1 will allow the technician to utilize larger diameter buffs and abrasives, while obtaining the accuracy and speed of interchanging both 3/32” [2.4 mm] and 1/4” [6.4 mm] burs, mandrels and chuck accessories while the lathe is in motion. This combination will pay for itself in time saved, while providing excellent concentricity for accurate, professional results in finishing appliances.
All chuck and maintenance accessories included.
115V/60Hz. Also available in 230V/50Hz at additional cost.
Shipping Wgt.: 45 lbs [20.4 Kg]
Unit Dimensions.: 18” W x 8” D x 9 1/4” H [45cm x 20.3cm x 23cm
In stock
16B-1 Lathe with Chuk Changer is the model 26 high base lathe with the 16 Chuk/Changer factory-installed on the right-hand side. The 16B-1 will allow the technician to utilize larger diameter buffs and abrasives, while obtaining the accuracy and speed of interchanging both 3/32” [2.4 mm] and 1/4” [6.4 mm] burs, mandrels and chuck accessories while the lathe is in motion. This combination will pay for itself in time saved, while providing excellent concentricity for accurate, professional results in finishing appliances. All chuck and maintenance accessories included. 115V/60Hz. Also available in 230V/50Hz with European plug type (model 16B-1-E) at additional cost. Shipping Wgt.: 45 lbs [20.4 Kg] Unit Dimensions.: 18” W x 8” D x 9 1/4” H [45cm x 20.3cm x 23cm] Instructions
Weight | 45 lbs [20.4 Kg] |
---|---|
Dimensions | 18” W x 8” D x 9 1/4” H [45cm x 20.3cm x 23cm] |
Composition: | Cast Iron |
Options: | Model 16B-1-E, 230V/50Hz |
Instruction Manual | 26A Red Wing Lathe Manual |
Additional information
Weight | 45 lbs |
---|---|
Dimensions | 25 × 13 × 13 in |
P26-03A End Bell Right Side
P26-03L End Bell Left Side
P26-04 Spacing Washers (Set 3)
P26-05 Spring Washers (Set 3)
P26-06 Bolt Thru w/nuts (4 Set)
P26-06A Bolt Thru (4 Set)
P26-06B Nuts Only (4 Set)
P26-07 Bearings (2 Set)
P26-08A 2-SPD Rotor Tapered Shaft
P26-09 Centrifugal Switch-26,27,28
P26-11A Stator – Two Speed
P26-12A Switch Hood – Two Speed
P26-14 Cordset Grounding Type
P26-15B Rocker Switch – 2 Speed
P26-16 Switch Washer
P26-17A Base-High: 6′ Shaft Height
P26-18A Bolts & Washers for High Base
P26-19 Base Plate
P26-22 Lubri-Plate-1-3/4 Oz Tube
P26-25 Red Plastic Caps R&L Side
P26-INSL Chuck Remover 1 Piece-Left
P26-INSR Chuck Remover 1 Piece-Right
P16-1 Special Collet
P16-10RW Clutch Complete for Red Wing
P16-11 Clutch Lining
P16-12 Clutch Lining Screws (3)
P16-15 Arbor Band Chuck 3/4″ Diameter
P16-16 Chuck, Tapered
P16-19 Tooth & Knife Stone Chuck
P16-2 Pop-out Spring
P16-20 S/S Mandrel 1-64 Screw
P16-22 Bearings Set of Two (Front & Rear)
P16-23 Spacer Washers for #16
P16-24 Center Shaft for 16 C/C
P16-25 Recess Collar
P16-26 Press on Retaining Ring
P16-27 C/C Housing Complete
P16-28 SET Set Screw for Handle of C/C
P16-29 Adjusting Washer for C/C
P16-3 Stop
P16-3S Set of 6 Stops
P16-4 Stop Lock Screw
P16-5 Master Collet for No. 16 Chuck Changer
P16-6 Special Collet
P16-7R Clutch Spring Right
P16-8 Collet Wrench
P16-9H Red Cushion Grip for Handle
P16-9SH Steel Handle for 16
P16-ADRW Red Wing Adapter