16B Chuck Changer Complete On 26A Red Wing Lathe
$1,204.34
The 16B features the Chuck Changer factory-installed on the right side of the 26A Low Base Red Wing Lathe, providing seamless chuck changing at both low and high speeds. With a simple movement of the activation handle, technicians can switch between 1/4” (6.4mm) and 3/32” (2.4mm) burs, mandrels, and chuck accessories without stopping the lathe.
In stock
The 16B features the Chuck Changer factory-installed on the right side of the 26A Low Base Red Wing Lathe, providing seamless chuck changing at both low and high speeds. With a simple movement of the activation handle, technicians can switch between 1/4” (6.4mm) and 3/32” (2.4mm) burs, mandrels, and chuck accessories without stopping the lathe.
Designed for efficiency and accuracy, this combination delivers excellent concentricity for professional results when finishing appliances. All chuck and maintenance accessories are included.
Power: 115V/60Hz (also available in 230V/50Hz with a European plug – 16B-E, additional cost)
Shipping Weight: 41 lbs (18.6 kg)
Unit Dimensions: 18 1/4” L × 8” W × 7 3/4” H (45 cm × 20 cm × 19 cm)
Construction: Cast Iron
Manual: 16B Red Wing Lathe Manual
P26-05 Spring Washers (Set 3)
P26-06B Nuts Only (4 Set)
P26-07 Bearings (2 Set)
P26-08A 2-SPD Rotor Tapered Shaft
P26-09 Centrifugal Switch-26,27,28
P26-11A Stator – Two Speed
P26-12A Switch Hood – Two Speed
P26-14 Cordset Grounding Type
P26-15B Rocker Switch – 2 Speed
P26-16 Switch Washer
P26-17 Base-Low: 4-1/2″ Shaft Height
P26-18 Bolts & Washers LO F/Low Base
P26-19 Base Plate
P26-22 Lubri-Plate-1-3/4 Oz Tube
P26-25 Red Plastic Caps R&L Side
P26-INSL Chuck Remover 1 Piece-Left
P26-INSR Chuck Remover 1 Piece-Right
P16-1 Special Collet
P16-10RW Clutch Complete for Red Wing
P16-11 Clutch Lining
P16-12 Clutch Lining Screws (3)
P16-15 Arbor Band Chuck 3/4″ Diameter
P16-16 Chuck, Tapered
P16-19 Tooth & Knife Stone Chuck
P16-2 Pop-out Spring
P16-20 S/S Mandrel 1-64 Screw
P16-22 Bearings Set of Two (Front & Rear)
P16-23 Spacer Washers for #16
P16-24 Center Shaft for 16 C/C
P16-25 Recess Collar
P16-26 Press on Retaining Ring
P16-27 C/C Housing Complete
P16-28 SET Set Screw for Handle of C/C
P16-29 Adjusting Washer for C/C
P16-3 Stop
P16-3S Set of 6 Stops
P16-4 Stop Lock Screw
P16-5 Master Collet for No. 16 Chuck Changer
P16-6 Special Collet
P16-7R Clutch Spring Right
P16-8 Collet Wrench
P16-9H Red Cushion Grip for Handle
P16-9SH Steel Handle for 16
P16-ADRW Red Wing Adapter
P26-03A End Bell Right Side
P26-03L End Bell Left Side
P26-04 Spacing Washers (Set 3)
P26-06A Bolt Thru (4 Set)
General Information:
Factory-installed on the right side of the 26A Low Base Red Wing Lathe allowing technicians to switch between 1/4” (6.4mm) and 3/32” (2.4mm) burs, mandrels, and chuck accessories without stopping the lathe.
Performance: 1/4 horsepower, 1725/3450 RPM two-speed
Electrical Requirements: 115V/60Hz (also available in 230V/50Hz with a E1/4uropean plug – 16B-E, additional cost)
Physical Specifications: Unit Dimensions: 18 1/4” L × 8” W × 7 3/4” H (45 cm × 20 cm × 19 cm)
Construction: Cast Iron
Features and Accessories: Includes 16-1 attachments for Chuck Changer: 2 mandrels for cutting discs, two stone chucks for small stone wheels, one arbor band for a sanding sleeve, one tapered spindle for a buffing wheel and one collet wrench to remove and clean collets.
Chuck throw-off on left-hand side for easy removal of chucks.